MS 7518 VER 1.0 DRIVER

While disconnecting the Safety Hook from the fixed bolt, it is necessary to keep an eye on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the fixed lever will spring back instantly. These two connectors connect to the ATX power supply and have to work together to ensure stable operation of the mainboard. Please note that any violation of the correct in s tal lati on p roc edur es m ay cause permanent damages to your mainboard. X Micro ATX mainboard. If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that no damage will be caused. Please turn off the power and unplug the power cord before installing the CPU.

Uploader: Arashisida
Date Added: 14 July 2004
File Size: 53.13 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 96866
Price: Free* [*Free Regsitration Required]

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. Make sure to raise the lever up to a degree angle. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that no damage will be caused.

Hardware Setup Hardware Setup This chapter tells you how to install the CPU, memory modules, and expansion cards, as well as how to setup the jumpers on the mainboard. The gold arrow should point as shown in the picture.

  HP DESKJET 1512 DRIVER DOWNLOAD

Mainboard photos shown in this section are for demonstration of the cooler installation for Socket CPUs only. Each Serial ATA connector can connect to 1 hard disk device. You can insert the expansion cards to meet your needs. Open Lever Sliding Plate 90 degree 2. The plastic clip at each side of the DIMM slot will automatically close. The Ultra ATA interface boosts data transfer rates between the computer and the hard drive up to megabytes MB per second.

MSI Ms-7518 P6ngm2 Motherboard SKT 775 Ddr2 NVIDIA Mcp73pv

To clear the password, open the jumper and restart your computer. Ger, desktop platforms with PCI Express Architecture will be designed to deliver highest performance in video, graphics, multimedia and other sophisticated applications.

Our products are under continual improvement and we reserve the right to make changes without notice. While disconnecting the Safety Hook from the fixed bolt, it is necessary to keep an eye on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the fixed lever will spring back instantly. Power supply of watts and above is highly recommended for system stability. Trademarks All trademarks are the properties of their respective owners.

Turn over the mainboard, and install the backplate to the proper position.

Meanwhile, read the documentation for the expansion card to make any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration.

Please turn off the power and unplug the power cord before installing the CPU. Place the power cord such a way that people can not step on it.

  C2110 ADSL MODEM USB DRIVER DOWNLOAD

MSI BIOS for MSI Motherboards MS

You must configure second hard drive to Slave mode by setting the jumper accordingly. If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. It’s a community-based project which helps to repair anything. Make sure the safety mms completely clasps the fixed bolt of the retention mechanism. JLPC1 The pin header is for internal debugging only.

Correc t CP U placement 4. Otherwise, the Line-Out connector on the back panel will not function.

MSI BIOS for MSI Motherboards MS-7518

Alternatively, please try the following help vver for further guidance. If any of the following situations arises, get the equipment checked by a service personnel: The module will only fit in the right orientation. Keep this equipment away from humidity.

Then push down the power supply firmly into the connector. Lay this equipment on a reliable flat surface before setting it up. Hook one end of the clip to hook first, and then press down the other end of the clip to fasten the cooling s et on the top of the retention mechanism.